Used Quadro Comils, Cone Mills, and Conical Mills

A cone mill sizes powders and granules by pushing them through a conical screen. An impeller turns inside the screen, and product falls in from the top by gravity or is drawn in under vacuum. Particles leave once they are small enough to pass through the screen holes. The screen, the impeller profile, and the speed set the final size. Because the action is gentle, a conical mill typically makes fewer fines and less heat than a hammer mill.

Federal Equipment Company stocks more than 30 used cone mills as part of our used mills inventory. Most are Quadro Comil machines, from bench-scale lab units to large production mills. We also carry cone mills and conical sieve mills from Glatt, Kemutec, and L.B. Bohle. Across the cone mills we handle, drives range from 0.25 to 25 HP, and nearly every unit is stainless steel. Most machines are held at our Cleveland, OH facility and are available for inspection.

Can't Find What You Need?

Request Sourcing Help Tell us the product, the target particle size, and the throughput you need. We will look for it across our network.

Sell Your Equipment We buy surplus Quadro Comils and other cone mills outright. Send us a list, and we will make an offer.

Browse our selection below and request a quote for more information regarding our Used Quadro Comils, Cone Mills, and Conical Mills.

You can also view our full on-hand inventory across all categories.

Need Parts for Comil / Cone / Conical Mills?

Discover a wide range of parts and purchase instantly at PharmParts.com .

Page 2

A conventional cone mill is used mainly for delumping and granule sizing rather than fine grinding. High-energy models are built to reach a finer particle size. A cone mill breaks up wet or dry granulation, sizes oversize granules after drying, and knocks down agglomerates in raw materials before blending. The product stays in the mill only until it passes the screen, so it usually sees little heat, and the particle size distribution is typically narrower than from impact milling.

Screen choice does most of the work. Round-hole screens give a controlled size, grater screens shear wet or sticky mass, and square-hole and slotted screens are typically used to pass coarse product quickly. The impeller profile and speed fine-tune the result, and a change of screen lets one mill run several products. Our parts division, PharmParts, sells screens, impellers, and parts for the Quadro Comil 194, 196, 197, U5, U10, U20, and U30, and our comil screens and parts category carries more.

Drive position separates the two main designs. Top-driven mills, such as Kemutec KEK cone mills, hang the impeller from a drive above the cone. Underdriven mills, such as the Quadro U10 and U20, put the drive below the screen and leave the inlet clear for direct feed from above. Conical sieves, including Glatt TR sieves and Quadro FlexSift units, look similar but do a different job: they screen out oversize and foreign material and break up soft agglomerates without reducing particle size.

Model families recur in this category, and buyers tend to search by them. Quadro Comil machines make up most of what we handle: the 193, 194, 196, 197, and 198 series, the U3, U5, U10, and U20, the H20 high-energy mill, and SLS lab systems. We also see Glatt GS220 cone mills, Kemutec KEK cone mills, L.B. Bohle BTS 200 cone mills, and Frewitt FreDrive mills with ConiWitt milling heads.


Applications & Industries

  • Solid dosage production: sizing wet granulation ahead of the dryer, milling dried granulation before blending and compression, and delumping excipients.
  • Pharmaceutical manufacturing: contained milling, with Comils mounted in isolators and gloveboxes, and ATEX- and explosion-proof-rated units for hazardous areas.
  • Food and beverage: sugar, spices, and powdered ingredients that clump in storage, milled on stainless steel machines.
  • Chemical processing: delumping pigments, resins, and dry chemical intermediates, and sizing agglomerated product after drying.
  • Laboratory and pilot work: bench-scale Quadro Comil 193, U3, and U5 mills and SLS lab systems for formulation work before a process is scaled up.

Specifications & Configurations

Specification Range
Drive power 0.25 to 25 HP
Impeller speed 180 to 7,200 rpm; larger mills run slower
Screen diameter About 3.25" to 24"
Throughput From lab batches of about 50 g to about 16,000 lb/hr, depending on product and screen
Particle size Down to about 150 µm on standard cone mills; about 20 µm (d50) on high-energy mills
Materials of construction 316L stainless steel product contact parts on current mills, 304 and 316 on many older ones
Hazardous-area ratings Explosion-proof and ATEX versions, to Zone 20 for dust and Zone 0 for gas; confirm the certificate for the specific mill

Design variants. Top-driven and underdriven cone mills, high-energy mills, bench-scale lab mills, conical sieve mills and turbo sieves, and modular drives with interchangeable milling heads.

Common options. Variable-speed drives with VFD controls, adjustable-height stands, hoist and lift mounts, feed hoppers and feed valves, isolator and glovebox mounting, and spare screen and impeller sets.


Why Buy Used

A new production cone mill is often built to order once the drive, rating, screen set, and containment are specified. A used mill of the same size typically costs a fraction of the new price, and in-stock units can often ship in weeks rather than months.

Cone mills hold their value because the parts that wear are the screens, impellers, and seals, and all of them can be replaced. A stainless steel housing and drive that have run clean product can have years of service left. On a specific mill, ask which screens and impellers come with it, whether the drive is fixed-speed or VFD, the voltage, and whether any hazardous-area certificate comes with the unit.

Every unit is inspected when it arrives at our Cleveland, OH facility, and it is available for customer inspection before purchase. Refurbishment and testing can be arranged upon request. Process validation for your own product and facility remains with the buyer.